成人无码H免费动漫在线观看,精品成A人无码亚洲成A按摩,亚洲暴爽AV天天爽日日碰,中文字幕人成人乱码亚洲影

歡迎來到滄州路儀試驗儀器有限公司網站!
技術文章
首頁 >>> 技術文章 >>> 瀝青軟化點測定儀英文版說明書

瀝青軟化點測定儀英文版說明書

瀝青軟化點測定儀英文版說明書

First, the applicable standard

This instrument was petroleum and petroleum products test method standards T3536-2000 GB/ "petroleum products-determination of Flash and fire (Cleveland Open Cup method) to design and manufacture.

This instrument also applies to JTJ052 2000 highway code T0611 2000 the asphalt for Flash and fire test (Cleveland Open Cup method) and the international prospective ISTMD 2000 test.

2. purpose and scope of application

The tester is applied to Cleveland Open Cup (hereinafter referred to as COC) determination of viscous oil bitumen, coal tar pitch and test 79 ° c above the liquid asphalt material for Flash and fire safety for construction use.

III. instruments and working conditions

        Power supply: 220V ± 10% 50H

        Ambient temperature: -10 ¡æ ~ 50 ¡æ

        Relative humidity: 85%

Fourth, the main features and technical parameter

 Automatic sweep stroke, ignition;

 Electric heating power 0 ~ 400W continuously adjustable;

 Heating wire consists of transparent quartz tube protection, no open flames, explosions, and the temperature rises rapidly;

5. block diagram of the main structure and principle

 

Structure, as Figure 1

                  Figure 1

Principle diagram of figure 2

Figure 2

VI. installation and use

1 , Open box, press the instrument integration and technical documentation to check instrument appearance and related accessories, such as damage or missing, according to the chart shown in the installation.

2 , Check the power supply and grounding is good.

3 , Turn the power switch, the led lights, then you can carry out test operations. 4, specimen Cup with solvent cleaning, drying, installed in the bracket.

5 , Installing thermometers, thermometers, vertical specimen Cup is inserted, the thermometer mercury bulb from the Cup about 6.5mm, location and relative side margin igniter glass edge 16mm.

6 , Sample preparation, sample Cup to marking and other parts of the sample Cup not stained with asphalt. (Note: the sample heating temperature should not exceed the following 55 flash point ℃)

7 , All equipment should be placed in the Interior light darker and no significant air circulation, and three-sided enclosure windscreen.

8 , Ignitor and gas-pressure vessel (e.g. liquefied propane gas or natural gas) with hose connection, turned the ignition, flame ignition testing, debugging into standard ball shape or diameter 4mm ± 0.8mm small spherical flame test.

7. test procedure

1 , Start heating test, so that the heating rate rapidly achieve 14 ¡æ /min ~ 17 ¡æ/min. When the sample temperature is expected to achieve before 56 flash point ℃, adjust the heater to reduce heating rate so that the expected Flash before 28 ° c can make heating rate control in 5.5 ¡æ /min ± 0.5 ¡æ /min.

2 , Sample temperature desired Flash before 28 ℃, every 2 ° c according to the ignition button once so that the flame igniter test centers along the test Cup 150mm RADIUS for arc level scan once, from the experimental side of the Cup to the other side of the elapsed time of about 1s. You should confirm that the pilot flame Igniter for diameter 4mm ± 0.8mm fireball, and is located in the test above 2.5mm Cup. (Note: the test is not a specimen Cup)

3 , When initially appears on the specimen surface in a moment that is off the blue flame, immediay credited from thermometers, temperature on reading as specimens of Flash. Note do not try to flame around the blue and white flame mistaken for the Flash fire.

4 , Continue to maintain sample heating, heating rate 5.5 ¡æ /min ± 0. 5 ¡æ /min, and press the required test CDI ignition.

5 , Immediay when the sample contact flame ignition and combustion can continue for a period of not less than 5s, stop heating, and read the temperature on the recording thermometer as a specimen.

6 At least the same specimen , parallel test twice, two measuring results is less than the margin of a repetitive test allows poor 8 ℃, the average value of the integer as a test result.

7 , Precision or allow poor

Repetitive test allows the poor to: flash point 8 ℃, lighted 8 ℃;

Reproducibility test allows for: flash point 16 ℃, lighted 14 ℃.

8 , After the end of the test, as well as the cleaning and should cut off the power.

VIII. 1, complete sets of equipment:

 

 

 

 

Ordinal

Name

Quantity

Spare parts

Quantity

Comments

1

Cleveland Open Cup flash point Tester Tester

1 Taiwan

 

 

2

Cleveland oil Cup

1 Only

 

According to the orders ' requirements

Increase the supply of spare parts

3

Igniter

1 Set

 

 

4

Thermometer

1 Root

 

 

5

Thermometer frame

1 Set

 

 

6

Power cord

1 Root

 

 

7

Fuse tube

1 Only

Alternate

8

Connection hose

1 Root

 

 

 

2 , Technical file

(1) manual 1 copies

(2) product warranty cards 1 copies

(3) certificate 1 copies

Examiner: packaging:

Year month day years /month

 

 

版權所有© 2018 滄州路儀試驗儀器有限公司

冀公網安備 13092902000113號

老中医吮她的花蒂和奶水视频播放| 扒开腿狂躁女人视频免费| 久久久久无码专区亚洲AV| 玩弄人妻少妇500系列网址| 欧美人与物VIDEOS另类| 欧美老熟妇乱大交XXXXX| 亚洲色熟女图激情另类图区| 久久久久久久99精品国产片| 曰韩无码二三区中文字幕| 国产精品久久高潮呻吟无码| 高H各种姿势调教1V1| 精品久久久久久亚洲综合网| 扒开双腿疯狂进出爽爽爽动态照片| 调教 SM 重口 H文 HY| 免费国产黄网站在线观看可以下载| 三个男人躁我一个爽视频免费| 麻豆人妻无码性色AV专区| 猛烈H继攵禁忌H| 最近韩国电影高清免费观看HD| 亚洲精品国产精品乱码不99| 青丝影院视频在线播放| 欧美FREE性XXXX护士HD| 18禁男女爽爽爽午夜网站免费| 色播久久人人爽人人爽人人片AV| 岳两片蚌肉缓缓张开| 亚洲AV永久一区二区三区| 女生和男生一起差差30分app| 你的棒棒可以桶桶我的下水道| 五十路○の豊満な肉体| 最近韩国电影高清免费观看HD| 小SAO货揉揉你的奶真大视频| 日本丰满熟妇BBXBBXHD| 久久久久国产精品熟女影院| 亚洲丰满少妇XXXXX高潮| 极品妇女扒开粉嫩小泬| 被黑人伦流澡到高潮HNP动漫| 中文无码熟妇人妻AV| 供人泄欲玩弄的妓女H| 精品无码人妻一区二区三区不卡| 精品国产一区二区三区AV片| 岛国AV无码精品一区二区三区|